Lens hood

Discussion in 'Bags, Tripods, and Accessories' started by Tony R, Dec 27, 2020.

  1. Tony R

    Tony R New Member

    Joined:
    Dec 27, 2020
    Messages:
    2
    Equipment:
    EOS-600D with 18-55mm 3.5-5.6 IS II lens
    Canon EF 50mm 1.8 STM
    Canon EFS 55-250mm 4.5-5.6 IS II lens
    Canon EFS 35mm 2.8 Macro lens
    I’ve bought a Canon EW-63C lens hood for my lens but I find that it has only 2 bayonet fittings compared to the three on my lenses. When screwed on, it does not feel secure so have I bought the wrong lens hood?
     
    Tony R, Dec 27, 2020
    #1

  2. Caladina

    Caladina Well-Known Member

    Joined:
    Jan 30, 2020
    Messages:
    1,779
    Equipment:
    Canon M50
    Canon 18-45mm m, Canon 18-150mm m, Canon 55-200mm m, Canon 22mm m, Canon 28mm m macro,
    Sigma 100-400c ef, Sigma 18-35mm art ef,
    7artisans 7.5mm m, Laowa 100mm macro ef, laowa 9mm zeroD m, Vintage M42 Lenses:
    Ashi Super - Takumar 1.8 / 55mm,
    depends which lens you bought it for.

    have you checked images online to make sure its genuine etc?
     
    Last edited: Dec 27, 2020
    Caladina, Dec 27, 2020
    #2
  3. Tony R

    Tony R New Member

    Joined:
    Dec 27, 2020
    Messages:
    2
    Equipment:
    EOS-600D with 18-55mm 3.5-5.6 IS II lens
    Canon EF 50mm 1.8 STM
    Canon EFS 55-250mm 4.5-5.6 IS II lens
    Canon EFS 35mm 2.8 Macro lens
    I’m sure it is genuine Canon as it came from a reputable online dealer. It was bought for the standard kit lens 18-55mm f3.5-5.6
     
    Tony R, Dec 27, 2020
    #3
  4. rayallen

    rayallen Well-Known Member Site Supporter

    Joined:
    Apr 26, 2017
    Messages:
    1,277
    That is the correct lens hood for that lens. I have that combination. Mine also does not attach tightly so you are not alone. The other problem that I have is that the front element rotates during focusing so the tulip lens hood can cause vignetting if it rotates to the wrong position. I am considering buying an after market round lens hood.
     
    rayallen, Dec 27, 2020
    #4
  5. Craig Sherriff

    Craig Sherriff Well-Known Member Site Supporter

    Joined:
    Apr 25, 2017
    Messages:
    3,173
    Location:
    Tasmania, Australia
    Equipment:
    60D, 10D, 50D 1dmark3, T70, AV1, lenses ranging from 28mm to 600 mm, canonet Junior, Canonet QL 25, Mamiya C3 and 3 lens sets,Mamiya 645 pro TL and 3 lenses. Pentax MG and various lenses, Toyoview 4 * 5 inch large format camera,Calimat C1 8*10 inch ultra large format camera.
    This is one of those, gosh darn moments, if it does not feel secure, you can get away with it by using a bit of electrical tape to secure it in place.
     
    Craig Sherriff, Dec 28, 2020
    #5
  6. johnsey

    johnsey Site Moderator Staff Member Site Supporter

    Joined:
    Apr 21, 2017
    Messages:
    2,131
    Location:
    Fargo, ND
    Equipment:
    5dMk4, 5dsR, 5dMk2, 20D, 70-200 2.8L IS, 100mm 2.8 Macro USM, 50mm 1.4, 85mm 1.8, 17-40mm 4.0L, TS-E 24mm 3.5L II, Rokinon 14mm 2.8; Pixma Pro-100
    This is the right hood, Canon uses two grooves on the hoods and ends of lenses that turn and clip in place.
     
    johnsey, Dec 28, 2020
    #6
  7. Caladina

    Caladina Well-Known Member

    Joined:
    Jan 30, 2020
    Messages:
    1,779
    Equipment:
    Canon M50
    Canon 18-45mm m, Canon 18-150mm m, Canon 55-200mm m, Canon 22mm m, Canon 28mm m macro,
    Sigma 100-400c ef, Sigma 18-35mm art ef,
    7artisans 7.5mm m, Laowa 100mm macro ef, laowa 9mm zeroD m, Vintage M42 Lenses:
    Ashi Super - Takumar 1.8 / 55mm,
    you can use a rubber band to tighten the grip of the loose lens hood by cutting the band so its a strip then laying it across the bayonet rather than around it and cutting off the access
     
    Caladina, Dec 28, 2020
    #7

Share This Page